90% of Bottled Water show Signs of Plastic Particles

Microplastics found in most bottled water

Bottled water is marketed as the very essence of purity. It’s the fastest-growing beverage market in the world, valued at US$147 billion per year.

But new research by  a nonprofit journalism organization based in Washington, D.C., Orb Media, shows that a single bottle can hold dozens or possibly even thousands of microscopic plastic particles.

Tests on more than 250 bottles from 11 brands reveal contamination with plastic including polypropylene, nylon, and polyethylene terephthalate (PET).

EXECUTIVE SUMMARY

  • Tested 259 individual bottles from 27 different lots across 11 brands
    • Purchased from 19 locations in 9 countries
  • 93% of bottled water showed some sign of microplastic contamination
    • After accounting for possible background (lab) contamination
  • Average of 10.4 microplastic particles >100 um per liter of bottled water
    • Confirmed by FTIR spectroscopic analysis
    • Twice as much as within previous study on tap water
  • Including smaller particles (6.5–100 um), average of 325 microplastic particles per liter
    • Identified via Nile Red tagging alone
    • No spectroscopic confirmation
    • Range of 0 to over 10,000 microplastic particles per liter
    • 95% are particles between 6.5–100 um in size
  • For particles > 100 um:
    • Fragments were the most common morphology (66%) followed by fibers
    • Polypropylene was the most common polymer (54%)
      • Matches a common plastic used for the bottle cap
    • 4% of particles showed presence of industrial lubricants
  • Data suggests contamination is at least partially coming from the packaging and/or the bottling process itself

CONCLUSIONS

Twenty-seven different lots of bottled water from 11 different brands purchased in 19 locations across 9 different countries were analyzed for microplastic contamination using a Nile Red stain, which adsorbs to polymeric material and fluoresces under specific wavelengths of incident light. The use of the fluorescent dye allowed for smaller particles to be detected as compared to a similar study of tap water using a Rose Bengal stain, though the analytical methods employed for their enumeration restricted the lower size limit to 6.5 micrometers.

Of the 259 total bottles analyzed, 93% showed signs of microplastics. There was significant variation even among bottles of the same brand and lot, which is consistent with environmental sampling and likely resulting from the complexities of microplastic sources, the manufacturing process and particle-fluid dynamics, among others. As bottle volume varied across brands, absolute particle counts were divided by bottle volume in order to produce microplastic particle densities that were comparable across all brands, lots and bottles. These densities were reduced by lab blanks in order to account for any possible contamination. Given our use of lab blanks, the inability to photograph the full filter, the lower limit of one pixel being equivalent to 6.5 micrometers, and control runs of the software employed to digitally count particles less than 100 micrometers, the numbers reported here are very conservative and likely undercounting, especially with regard to smaller microplastics (<100 micrometers), which were found to be more prominent (on average 95%) as compared to particles greater than 100 micrometers (on average 5%).

Infrared analysis of particles greater than 100 micrometers in size confirmed microplastic identity and found polypropylene to be the most common (54%) polymeric material (at least with regard to these larger microplastics), consistent with a common plastic employed to manufacture bottle caps. Smaller particles (6.5–100 micrometers) could not be analyzed for polymer identification given the analytical limits of the lab. While these smaller particles could not be spectroscopically confirmed as plastic, Nile Red adsorbs to hydrophobic (‘water-fearing’) materials, which are not reasonably expected to be naturally found within bottled water. Our FTIR analysis of larger (>100 um particles) fluorescing particles, all of which were confirmed to be polymeric, provides additional support of the selective binding of NR to microplastic particles within the samples. Even further, Schymanski et al. (2018) did spectroscopically confirm (via Raman) particles within this smaller size range in German bottled water as being polymeric in nature provide additional support for their presence. Given this and following the conclusions of prior studies (e.g., Maes et al. (2017) and Erni-Cassola et al. (2017)) the adsorption of Nile Red alone was used to confer microplastic identity to these smaller particles. As the specific polymer content could not be determined, they could very well show a different compositional pattern as compared to the larger particles analyzed. This could explain the difference in our polymeric compositional analysis relative to a very recent and similar analysis of bottled mineral waters by Schymanski et al. (2018), which found PEST (polyester+polyethylene terephthalate) to be the most common polymeric material, consistent with a common plastic employed to manufacture the bottle itself. Either way both studies indicate that at least part of the microplastic contamination is arising from the packaging material &/or the bottling process itself.

Author: DES Daughter

Activist, blogger and social media addict committed to shedding light on a global health scandal and dedicated to raise DES awareness.

Have your say! Share your views

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

w

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.